Bilco's Bodgements #6

A home for threads which don't relate to minimum(ish) gauge railways

Moderator: GnATTERbox Moderators

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Bilco's Bodgements #6

Postby Bilco » Sat Mar 13, 2021 3:50 pm

Right, having cleared the Bodgeneerium of the locotracteur I started to think of the next bodgement. I found an intriguing image online ...

Image

That could be an interesting bodge, given the right ingredients ...

So, a melange has been assembled, courtesy of t'Bay ...

Image

From the top - a Teamsterz saddle tank loco ( with a strange tender), a Lima HO diesel loco, and a workman's coach body kit from 422 Modelmaking.

Casting the tender aside, the unpacked loco looks like this ...

Image

And the loco disembowled looks like this ...

Image

The cab and tank top are a one-piece metal casting, while the rest is plastic ...

A (very) rough 'design' session leads me to think that it's not a bodge too far ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums

User avatar
chris stockdale
Millegniumer
Millegniumer
Posts: 1295
Joined: Wed Jul 09, 2003 9:44 am
Location: Market Drayton, Shropshire, UK
Interests: most things narrow gauge, model or full size, especially 7 1/4" 'minimal' (which is sub Heywood ride on)

Re: Bilco's Bodgements #6

Postby chris stockdale » Sat Mar 13, 2021 5:43 pm

The phrase, ‘You don’t have to be mad, but it helps’ comes to mind for some reason. :D

Cheers,

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Re: Bilco's Bodgements #6

Postby Bilco » Wed Mar 17, 2021 3:38 pm

Well Chris, my advanced mental bereftness was diagnosed a long time ago ...

Anyway, I've made a start on the coach sides ...

Image

The sides and an end as 422 made them ...

Image

The end result of a chopping session ...

Image

The end result of a glueing session. The prototype sides have 4 windows, but as I'm bodging a 'like' rather than a 'same-as' I can live with that. The cab won't have an access door to the coach, so a piece of styrene sheet will do for that, and also for the cab front ...

On measuring the saddle tank it looks like I'll have to shorten it and remove the cab - the pile of rejected bits will be much bigger than the bit I use, as usual ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Re: Bilco's Bodgements #6

Postby Bilco » Tue Mar 23, 2021 7:23 pm

The cut-up-and-stuck-together bits now assembled into the coach body ...

Image

From the back, showing the door onto the rear balcony ...

Image

... and from the front, showing the arched door into the cab and the cab front ...

A good solid false roof ensures that all is firm and square ...

Ok - square-ish ...

I thought I was going to have a lot of filling and filing to do on the joins of the stuck together bits, then tried a couple of strips of styrene glued over the worse joins. A dozen pieces of styrene strip later ...

Now to work on the chassis of the diesel loco ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums

DCRFAN 3
GnatterBox Centurion
GnatterBox Centurion
Posts: 158
Joined: Sun Jun 14, 2015 10:45 pm
Location: Wellington NZ

Re: Bilco's Bodgements #6

Postby DCRFAN 3 » Wed Mar 24, 2021 10:44 am

Looking good

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Re: Bilco's Bodgements #6

Postby Bilco » Tue Mar 30, 2021 6:40 pm

Work on the chassis. The first thing I did was remove the motor bogie and the unpowered bogie, and cut off the box from the underside ...

Image

The hole was filled with 2mm styrene sheet to strengthen the chassis, and more 2mm and 1mm styrene sheet was used to level up the top surface. The chassis was widened by the addition of 3mm styrne strip along the edges- 6mm deep under the coach body and 3mm deep under the boiler ...

Image

Buffer beams were also added front and rear - the front one is deeper, because I'm going to fit SKIRTS!! The horror ...

But I'm not going to mess with the motor bogie to add coupling and connecting rods, cross-heads and slide bars, so hiding the bogie is the only thing for it ...

The coach body sitting in place just to show how it'll look ...

Image

So, next task is to plate over the top of the chassis with 0.5mm sheet and fit those skirts ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Re: Bilco's Bodgements #6

Postby Bilco » Sun Apr 04, 2021 6:45 pm

So - chassis top plated - tick, skirts fitted - tick ...

I started work on the body of the loco part of the infernal contraption. Not much left of the original ...

Image

... just a length of the tank, cut to remove the cab and two of the holes for the vastly oversize handrails. The 'dome' was removed and, as the tank is a bit shallow, I glued some strips of 2mm styrene to the bottom edge. Then a piece of 0.5mm styrene sheet was superglued over the remaining holes ...

I had misjudged how much the motor bogie has to swing - the skirts already limit that a little - so I had to fix the lower 'boiler' sides further out from the centre than I had hoped ...

So, the bits propped together to see how it looks ...

Image

I see that I'd also misjudged where to make the holes in the cab front, despite 'careful' measuring. Looks like the next job is making a new cab front ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums

User avatar
Bilco
Millegniumer
Millegniumer
Posts: 1107
Joined: Mon Oct 29, 2007 3:55 pm
Location: Woodstock, Oxfordshire
Interests: 7mm & 16mm NG, Gn15

Re: Bilco's Bodgements #6

Postby Bilco » Tue Apr 13, 2021 7:08 pm

Progress crawls on ...

A new cab front has been made and fitted. The boiler/tank section has been modified to make a better attempt at the shape of the smokebox, and the resulting holes diguised with valve covers. I hope to distract the eye from the width of the side sheets under the tank, needed to give the motor bogie some decent swivel movement, by the addition of assorted bits of iron-mongery. The skirts over the assumed motion have been decorated with hinged access panels ...

Image

Image

What may not be so obvious is that the chassis has been lengthened by 4mm - two inserts of 2mm styrene front and rear - to give a bit more footplate in front of the smokebox, and bigger steps at the rear.

The photos were taken in strong raking light, and reveal that some more filling and sanding is required ...

Hours of fun ...
Bill

If at first you don't succeed, cheat.
Too soon old, too late smart.

https://sites.google.com/site/myoldlayouts/
https://www.flickr.com/photos/149926300@N07/albums


Return to “gNot Minimum Gauge”

Who is online

Users browsing this forum: No registered users and 2 guests